.

Category Archives: Rental Equipment

  • Home
  • Category Archives: "Rental Equipment"
Olympus Omniscan MX2 32:128PR Ultrasonic Phased Array Flaw Detector
Stock# 150514BA
This is a clean, good condition Olympus Omniscan MX2 with a 32:128PR module installed. The 32:128PR module is in great shape, with the connectors all in good, clean condition, and no signs of abnormal usage. The Omniscan MX2 is one of the most sought after phased array units, as it is the premium PA unit from Olympus. For everything listed, you would expect to pay over $88,300 for this equipment new. Here is the opportunity to get it in good condition, ready to use, for 50% off retail. The unit can be tested in our retail store in Pooler, GA, if you would like to examine the unit before you purchase.
Included with the sale is the following:
-Omniscan MX2 32:128PR Phased Array Flaw Detector
-Tomoview Software
-Charger/Cables
-2 Batteries
-SD Card
-Software Card Reader
-Rolling Hard Case
-Manual
-Calibration (including Certificates)
SPECIFICATIONS:
Module OmniScan Onboard Acquisition OmniScan Using TomoView Control Available Analysis Software
UT MXU 4.1R12 TomoView 2.10R16 with OSTV PA1 3.0R8 OmniPC 4.1R12
TomoView 2.10R16
PA MXU 4.1R12 TomoView 2.10R16 with OSTV PA1 3.0R8 OmniPC 4.1R12
TomoView 2.10R16
UT2 MXU 4.1R12 TomoView: TBD OmniPC 4.1R12
TomoView 2.10R16
PA2 MXU 4.1R12 TomoView 2.10R16 with OSTV PA2 1.0R2 OmniPC 4.19
TomoView 2.10R16

Please note that files generated with previous software versions are supported by the latest releases.

OmniScan MX2 Mainframe Specifications

General
Overall dimensions
(W x H x D)		 325 mm x 235 mm x 130 mm
(12.8 in. x 9.3 in. x 5.1 in.)
Weight 3.2 kg (7 lb), no module and one battery
Data Storage
Storage devices SDHC card, most standard USB storage devices, or fast Ethernet
Data file size 300 MB
I/O Ports
USB ports 3
Audio alarm Yes
Video output Video out (SVGA)
Ethernet 10/100 Mbps
I/O Lines
Encoder 2-axis encoder line (quadrature, up, down, or clock/direction)
Digital input 4 digital TTL inputs, 5 V
Digital output 4 digital TTL outputs, 5 V, 15 mA
Acquisition on/off switch Remote acquisition enabled TTL, 5 V
Power output line 5 V, 500 mA power output line (short-circuit protected)
Alarms 3 TTL, 5 V, 15 mA
Analog output 2 analog outputs (12 bits) ±5 V in 10 kΩ
Pace input 5 V TTL pace input
Display
Display size 26.4 cm (10.4 in.) (diagonal)
Resolution 800 pixels x 600 pixels
Brightness 700 cd/m2
Number of colors 16 million
Type TFT LCD
Power Supply
Battery type Smart Li-ion battery
Number of batteries 1 or 2 (battery chamber accommodates two hot-swappable batteries)
Battery life Minimum 7 hours with two batteries
Environmental Specifications
Operating temperature range -10 °C to 45 °C
(14 ºF to 113 ºF)
Storage temperature range -20 °C to 60 °C (-4 ºF to 140 ºF) with batteries
-20 °C to 70 °C (-4 ºF to 158 ºF) without batteries
Relative humidity Max. 70% RH at 45°C noncondensing
Ingress Protection Rating Designed for IP66
Shockproof rating Drop-tested according to MIL-STD-810G 516.6
MX2 Module Compatibility
MXU 4.1R8 and later OMNI-M2-PA32128PR
MXU 4.0 and later OMNI-M2-PA1664
OMNI-M2-PA16128
OMNI-M2-PA32128
OMNI-M2-UT-2CH
MXU 3.1 and MXU 4.1R12 and later OMNI-M-UT-8CH
MXU All versions OMNI-M-PA1664
OMNI-M-PA16128
OMNI-M-PA32128
OMNI-M-PA32128PR
OMNI-M-PA3232 (200 V)
MXU-M 3.1 and previous OMNI-M-PA1664M

Phased Array Module Specifications (Applies to OMNI-M2 modules)

General
Overall dimensions
(W x H x D)		 226 mm x 183 mm x 40 mm
(8.9 in. x 7.2 in. x 1.6 in.)
Weight 1.6 kg (3.5 lb)
Connectors 1 Phased Array connector: Olympus PA connector
2 UT connectors: LEMO 00
Number of focal laws 256
Probe recognition Automatic probe recognition
Pulser/Receiver
Aperture 32 elements*
Number of elements 128 elements*
Pulser PA Channels UT Channels
Voltage 40 V, 80 V, and 115 V 95 V, 175 V, and 340 V
Pulse width Adjustable from 30 ns to 500 ns, resolution of 2.5 ns Adjustable from 30 ns to 1,000 ns; resolution of 2.5 ns
Pulse shape Negative square pulse Negative square pulse
Output impedance (32:128PR model) 35 Ω in pulse-echo mode
30 Ω in pitch-catch mode		 < 30 Ω
Output impedance (all other models) 25 Ω < 30 Ω
Receiver PA Channels UT Channels
Gain 0 dB to 80 dB, maximum input signal 550 mVp-p (full-screen height) 0 dB to 120 dB maximum input signal 34.5 Vp-p (full-screen height)
Input impedance (32:128PR model) 50 Ω in pulse-echo mode
90 Ω in pitch-catch mode		 60 Ω in pulse-echo mode
50 Ω in pitch-catch mode
Input impedance (all other models) 65 Ω 60 Ω in pulse-echo mode
50 Ω in pitch-catch mode
System bandwidth 0.6 MHz to 18 MHz (-3 dB) 0.25 MHz to 28 MHz (-3 dB)
Beamforming
Scan type Sectorial and linear
Group quantity Up to 8
Data Acquisition
Digitizing frequency 100 MHz
Maximum pulsing rate Up to 10 kHz (C-scan)
Data Processing PA Channels UT Channels
Number of data points Up to 8,192
Real-time averaging 2, 4, 8, 16 2, 4, 8, 16, 32, 64
Rectifier RF, full wave, half wave +, half wave –
Filtering 3 low-pass, 3 band-pass, and 5 high-pass filters. 3 low-pass, 6 band-pass, and 3 high-pass filters (8 low-pass filters when configured in TOFD)
Video filtering Smoothing (adjusted to probe frequency range)
Data Visualization
A-scan refresh rate Real time: 60 Hz
Data Synchronization
On internal clock 1 Hz to 10 kHz
On encoder On 2 axes: from 1 to 65,536 steps
Programmable Time-Corrected Gain (TCG)
Number of points 32: One TCG curve per focal law
Alarms
Number of alarms 3
Conditions Any logical combination of gates
Analog outputs 2

* Aperture and number of elements vary with each model. Current shipping models feature 16:64, 16:128, 32:128 configurations.

 

Trade Ins: We offer some of the highest prices on your used test equipment. We do partial trade ins or will buy your used equipment outright. An estimated trade in value will be assessed within 24 hours of receiving a value request.
Payment terms: We accept payment prior to shipping by Visa, MasterCard, AMEX, and Paypal (up to $10.000). Businesses and Universities, please call for payment options. Please notify us of method of payment in a timely fashion after the auction has ended. If a buyer has not made any attempt to contact us 7 days after this auction’s end time we will assume they are forfeiting the auction and the item will no longer be available to them.
International Buyers: We reserve the right to accept or decline international Paypal and credit cards. International shipping is available, but clearing customs will often result in delivery delays.
Shipping Terms: Buyer pays for shipping and packaging for this item. International buyers will pay for shipping charges to their country.

* Shipping and handling fees are not refundable under any circumstances. In the case of a return, the buyer is responsible for all shipping fees.
* Shipping for international buyers will be invoiced separately from the purchased product due to the high expense of shipping charges.
* Your phone number is required for shipping purposes, so please provide it with all correspondence.
* Please note that calculated shipping is based on UPS. We also reserve the right to ship for the same cost via FedEx or other carriers.
Packaging: All items will be packaged with materials necessary to ensure that the equipment will be adequately protected from the shipping process.
Feedback: We appreciate Positive feedback. We leave feedback as soon as we get feedback from you. If you have any problems with the sale, please try to resolve it with us before you leave us a Neutral or Negative feedback.

Warranty: No warranty is expressed or implied with any unit. All sales include a 3 day right of return (ROR). For any reason, within 72 hours of taking possession of the item, the buyer can return the item for a complete refund minus all shipping costs.
Return Policy: You can return the item for any reason within three days. We put great effort into thoroughly documenting each piece of equipment, typically with very detailed pictures and video clips. We strongly encourage you to study these images closely before you commit to purchasing the item. Please call or email us if you have any questions about anything that you are uncertain about. It is critical that you confirm that this item suites your needs within the three day return policy period. Any returns after two weeks will not be entertained, and we will automatically escalate to Ebay. If you choose to open an Ebay return case, and we are forced to accept the return, you are responsible for the following:

*Return Shipping and insurance of the item to our Store at the following address:

GP-Technical
246 Pooler Parkway Suite E
Pooler, GA 31322
*A Restocking fee of 10% of the purchase price for every week (after the initial 3 day return period) that the item is in your possession, not to exceed two weeks.
Sonatest DryScan 410D Ultrasonic Composite Flaw Detector
Stock # 150610A
The Sonatest DryScan is the top of the line flaw detector from Sonatest, offering capabilities not found in other units. The Dryscan is one of the few units available that can do normal ultrasonic inspection, as well inspect a number of different materials, including all of the following:
-Wood Laminate
-Friction Material
-EB Welding
-Ceramics
-Trees (center core disease)
-HoneyComb sections in Aluminium, Stainless and Paper
-Plastics/Rubber Composites
-Root Pass Weld
-Tires
-Carbon Products
-GRP/CFRP
-Conveyor Belts
-Bonding of Dissimilar Metals
The unit has the capability to dry couple with materials, opening a wide array of materials for inspection. The Dryscan is compatible with a number of different scanners, and has C-scan like capabilities. The DryScan is a current unit from Sonatest, so it will have parts support for the immediate future, along with additional accessories. For more information on the DryScan, visit the Sonatest website and get yourself an amazing deal on extremely rare unit!
Included with sale is the Following:
-Sonatest DryScan 410D
-Sonatest LiPo Battery
-Sonatest LiPo Charger
 
 

Specifications:

The dry coupling technique offers a number of considerable advantages. For example when a wide spectrum of transmitted signals is used, many of the geometric considerations conventionally applied in ultrasonic’s can be ignored. Typically, the transmitter and receiver transducers need not be in alignment, they can be oriented at a right angle to each other. This characteristic, plus the fact that the transducer tip can be as small as 5mm diameter, enables testing to be achieved that cannot be dealt with by conventional means.

With the Dryscan technique, highly effective signal transmission can now be achieved by using a completely dry contact system. The ultrasonic energy is coupled between the transducers and the material under test by using special plastic pads on the transducers, eliminating the need for a coupling medium. Transducers can be held or they may be roller type for continuous pass scanning using various manual or automatic manipulation systems, which can be linked to C-Scan recording systems. The Dryscan 410D concept is simple to apply and requires only a minimum of operator training. This technique results in no possible hazards of radiation, contamination or degradation of the test pieces.

Advantages of the System

The main advantages of the Shadow Technique is summarized below:

 

  • No coupling medium is required to contact the transducers acoustically to the test material.
  • Many of the geometric considerations applied to conventional ultrasonic detection methods can be ignored.
  • The system is highly reliable for fault detection.
  • The method can be used for many materials as a GO or NO-GO system – semi – or fully automatic.
  • In many cases, materials surface preparation is not necessary.
 

Test Range: 0 – 1mm (0.05in) up to 0 – 20000 mm (800 in.) at steel velocity. Variable in 1,2,5 sequence or continuously in 1mm (0.05in) increments.

Velocity: 256 to 16000m/s continuously variable.

Probe Zero: 0 to 999.999 μs, continuously variable.

Delay: Calibrated delay from 0 -20000mm in 0.05 mm steps at steel velocity (0-400in. in 0.002 in. steps).

Gain: 0 to 110dB. Adjustable in 0.1, 0.5, 1, 2, 6, 10, 14 and 20dB steps.

Test Modes: Pulse echo and transmit/receive.

Pulser: 100V – 450V square wave pulser. Pulse width from Spike to 2500ns duration – rise/fall times <10ns into 50 ohms at 200V: Width adjustable in 2% of nominal width, minimum 1ns maximum 40ns.

ActiveEdge™ Unique active pulse control for enhanced near surface resolution and signal response.

P.R.F: Selectable 15 to 5000Hz in 5Hz steps.

Update Rate: 60Hz (NTSC Mode); 50Hz (PAL Mode).

Rectification: Full wave, positive or negative half wave and unrectified rf.

Frequency Range: 7 narrow bands centred at 0.25Mhz, 0.5MHz, 1MHz, 2.25MHz, 5MHz, 10MHz and 15MHz. Broad band at 2 MHz to 22MHz (-6dB) and 1MHz to 35 MHz (-20dB). Special Dryscan mode allowing the resonant frequency of the receiver stage of the Dryscan 410 to be adjusted between 150kHz and 1.42MHz in 10 kHz steps.

Measurement Modes

Mode 1:Signal Monitor

Mode 2:Depth and amplitude of first signal in gate.

Mode 3: Echo-to-Echo distance measurement. (single gate)

Resolution: To 0.01mm (0.001in) for distance measurement or 1% FSH for amplitude measurement. Large display of measurement at top of A-Scan display. Measurement mode selectable between peak and flank.

A-Scan Memory: Maximum of 800 waveforms can be printed or transferred to a PC using optional SDMS software.

Panel Memory: 100 stores for retaining calibrations.

DAC: DAC defined by up to 10 points and digitally drawn on screen. DAC curves meet requirements of EN 1714, JIS and ASME standards, selectable between -2, -6, -10, -12 and -14dB. Amplitude read out selectable between % DAC, % FSH or relative dB.

Trade Ins: We offer some of the highest prices on your used test equipment. We do partial trade ins or will buy your used equipment outright. An estimated trade in value will be assessed within 24 hours of receiving a value request.
Payment terms: We accept payment prior to shipping by Visa, MasterCard, AMEX, and Paypal (up to $10.000).  Businesses and Universities, please call for payment options.  Please notify us of method of payment in a timely fashion after the auction has ended. If a buyer has not made any attempt to contact us 7 days after this auction’s end time we will assume they are forfeiting the auction and the item will no longer be available to them.
International Buyers: We reserve the right to accept or decline international Paypal and credit cards. International shipping is available, but clearing customs will often result in delivery delays.
Shipping Terms:  Buyer pays for shipping and packaging for this item. International buyers will pay for shipping charges to their country.  
 
* Shipping and handling fees are not refundable under any circumstances. In the case of a return, the buyer is responsible for all shipping fees.
* Shipping for international buyers will be invoiced separately from the purchased product due to the high expense of shipping charges.
* Your phone number is required for shipping purposes, so please provide it with all correspondence.
* Please note that calculated shipping is based on UPS.  We also reserve the right to ship for the same cost via FedEx or other carriers.
Packaging:  All items will be packaged with materials necessary to ensure that the equipment will be adequately protected from the shipping process.
Feedback:  We appreciate Positive feedback. We leave feedback as soon as we get feedback from you. If you have any problems with the sale, please try to resolve it with us before you leave us a Neutral or Negative feedback.

Warranty:  No warranty is expressed or implied with any unit. All sales include a 3 day right of return (ROR).  For any reason, within 72 hours of taking possession of the item, the buyer can return the item for a complete refund minus all shipping costs.
Return Policy:  You can return the item for any reason within three days. We put great effort into thoroughly documenting each piece of equipment, typically with very detailed pictures and video clips.  We strongly encourage you to study these images closely before you commit to purchasing the item. Please call or email us if you have any questions about anything that you are uncertain about. It is critical that you confirm that this item suites your needs within the three day return policy period. Any returns after two weeks will not be entertained, and we will automatically escalate to Ebay. If you choose to open an Ebay return case, and we are forced to accept the return, you are responsible for the following:
*Return Shipping and insurance of the item to our Store at the following address:
GP-Technical
246 Pooler Parkway Suite E
Pooler, GA 31322
*A Restocking fee of 10% of the purchase price for every week (after the initial 3 day return period) that the item is in your possession, not to exceed two weeks.
GE Inspection Hocking Locator 3S Eddy Current Flaw Detector
Stock # 150622B
 
This is a extremely clean instrument, that looks like it has been rarely used. All buttons and dials function as they should and the screen is in great shape. The locator series is an inspectors favorite, as it is lightweight, with a small frame and large screen. The end result is inspection after inspection with little, to no fatigue. The screen is easily viewed indoors or out, and the unit is known for its easy, one-handed use. The lithium-Ion batteries used in the Hocking series are capable of operating the unit for more than 8 hours at a time. Take advantage of this low price and grab one of GE’s most advanced Eddy Current flaw detectors at an extremely reduced rate.
 
Included with the Sale
-GE Hocking Eddy Current Flaw Detector
-Li-Ion Charger/Cable
-GE Hocking Li-Ion Battery
 
 
Specifications:
 

Key features

  • Advanced LCD allows easy viewing in all light levels
  • Band Pass and Ultra filters
  • Compatible with most existing probes
  • Conductivity and Coating Thickness modes
  • Finds flaws and corrosion in metal components and structures
  • Independent X & Y gain adjustment
  • Light & portable – weighs just 0.94 kg
  • Lithium-ion batteries typically run for up to 8 hours from a full charge
  • Output via RS232
  • Phase Plane/YT display modes
  • Similar interface to Locator 2 allowing easy cross-training
  • Simple set-up procedure
  • Single Frequency Eddy Current Unit
  • Storage of 50 setups and up to 50 traces
  • Trace record with parameter adjustment to optimise signal

Applications

  • General Crack Detection – Locator 3s can be used with a wide range of probes to detect surface-breaking and sub surface cracks. Adapters are available, allowing you to use other manufacturers probes.
  • Conductivity Measurement – Locator 3s can measure the conductivity of metals. This can, among other things aid in the veri?cation of material hardness and in the identi?cation of materials as part of a quality control system.
  • Coating Thickness Measurement – This function can be used to measure non-conductive coatings such as paint, and is often used as a quality control measure in the surface coating industry.
  • Weld Inspection – Locator 3s can be used with Hocking s specially designed WeldScan probes to reliably and accurately test for cracks in welds.
  • Fastener Inspection – Metal around fasteners, such as those found on aircrafts, must be inspected regularly to ensure their material integrity. Locator 3s, coupled with the appropriate probe, can easily and quickly carry out such inspections.
  • Thread Inspection – Thread inspection is carried out in a range of industries, including aerospace, petrochemical, civil engineering and automotive. Locator 3s provides the ideal solution to ensure quality, safety and reliability.
Operating Frequency Normal: 60Hz to 6 MHz (198 steps per decade adjustment) Conductivity: 60kHz
Display Display LCD with LED backlight. Protected by hard coated acrylic window. 480 x 320 pixel resolution 115 x 78mm viewable area
Gain Adjustable together or as independent X and Y control for ultra precise setting. 0dB to 88dB overall in 0.1dB steps Input gain selectable 0d
Low and High Pass Filters Low Pass : 3Hz to 2kHz in more than 500 steps High Pass : DC to 1.95kHz in more than 5000 steps
Alarms Alarm options are: + and levels, Sector and Box Gate. Flashing LED s, internal sounder
Phase 0 to 359.9 degrees in 0.1 degree steps.
Internal data storage Capacity for up to 50 traces and 50 settings. 28 character alphanumeric names, plus time and date stamps. Dynamic data may be recorded and r
Conductivity and Coating Thickness Measurement Capable of measuring electrical conductivity of materials in the range from 1 to 110% IACS
Probe compatability Absolute Locator (100 ohm impedance) Absolute standard (50 ohm impedance) Bridge Re?ection Hocking Conductivity Probes
Balance Load Manual or automatic. Selection from 1.3, 8.2, 22, 47, 82 or 120 ìH
Outputs Standard RS232 via 5 way Lemo
PC Connectivity Dedicated windows software allows easy reporting and printing.
Languages English, French, German, Spanish, Portuguese
Battery charger/eliminator 90 to 264 VAC, 47 to 440Hz
Probe connection Via 7 way Lemo

Trade Ins: We offer some of the highest prices on your used test equipment. We do partial trade ins or will buy your used equipment outright. An estimated trade in value will be assessed within 24 hours of receiving a value request.
Payment terms: We accept payment prior to shipping by Visa, MasterCard, AMEX, and Paypal (up to $10.000).  Businesses and Universities, please call for payment options.  Please notify us of method of payment in a timely fashion after the auction has ended. If a buyer has not made any attempt to contact us 7 days after this auction’s end time we will assume they are forfeiting the auction and the item will no longer be available to them.
International Buyers: We reserve the right to accept or decline international Paypal and credit cards. International shipping is available, but clearing customs will often result in delivery delays.
Shipping Terms:  Buyer pays for shipping and packaging for this item. International buyers will pay for shipping charges to their country.  
 
* Shipping and handling fees are not refundable under any circumstances. In the case of a return, the buyer is responsible for all shipping fees.
* Shipping for international buyers will be invoiced separately from the purchased product due to the high expense of shipping charges.
* Your phone number is required for shipping purposes, so please provide it with all correspondence.
* Please note that calculated shipping is based on UPS.  We also reserve the right to ship for the same cost via FedEx or other carriers.
Packaging:  All items will be packaged with materials necessary to ensure that the equipment will be adequately protected from the shipping process.
Feedback:  We appreciate Positive feedback. We leave feedback as soon as we get feedback from you. If you have any problems with the sale, please try to resolve it with us before you leave us a Neutral or Negative feedback.

Warranty:  No warranty is expressed or implied with any unit. All sales include a 3 day right of return (ROR).  For any reason, within 72 hours of taking possession of the item, the buyer can return the item for a complete refund minus all shipping costs.
Return Policy:  You can return the item for any reason within three days. We put great effort into thoroughly documenting each piece of equipment, typically with very detailed pictures and video clips.  We strongly encourage you to study these images closely before you commit to purchasing the item. Please call or email us if you have any questions about anything that you are uncertain about. It is critical that you confirm that this item suites your needs within the three day return policy period. Any returns after two weeks will not be entertained, and we will automatically escalate to Ebay. If you choose to open an Ebay return case, and we are forced to accept the return, you are responsible for the following:

*Return Shipping and insurance of the item to our Store at the following address:

GP-Technical
246 Pooler Parkway Suite E
Pooler, GA 31322
*A Restocking fee of 10% of the purchase price for every week (after the initial 3 day return period) that the item is in your possession, not to exceed two weeks.